This paper makes systematic reserch about the calculation of the assembling size chain formed by adjusting method with group spacers.

本文系統研究了用分組墊片法解裝配尺寸鏈時的計算方法。

Analysis about pinion gear bearing shim measuring influence factors & optimization in re-checking scheme

主齒軸承墊片測選的機理分析及復測方案優化

Remove the depth shims from rear pinion bearing cup bore in axle housinRecord the thickness of the depth shims.

從軸管里的后小齒輪軸承蓋孔拆卸限深墊片。記錄限深墊片厚度。

Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.

在軸殼內（沒有墊片）安裝差速箱和模型軸承，并緊固固定帽螺栓。

shielded ball bearing

帶防護墊圈的滾珠軸承

By measuring all dimensions associated with bearing, the shim dimension satisfying the requirements of bearing bore dimension was calculated to finally reach the requirements of assembly.

通過測量軸承各相關件的尺寸,計算出滿足軸承內孔尺寸要求的墊片厚度,最終達到裝配要求。

A bushing or similar lining for a bearing, made from a copper alloy.

銅套或銅襯墊用銅合金制的軸承軸瓦或套筒式襯墊

Bolt( screw, nut, stud, spring washer, pin, ball bearing, roller bearing) is the most commonly used machine part.

螺栓（釘、帽、頭螺栓、簧墊圈、、珠軸承、柱軸承）最常用的機械零件。

Plain bearings-Ring type thrust washers made from strip-Dimensions and tolerances

GB/T10446-1989滑動軸承整圓止推墊圈尺寸和公差

Plain bearings-Pressed bimetallic half thrust washers -Features and tolerances

GB/T10447-1989滑動軸承半圓止推墊圈要素和公差

Place 4 adapter blocks so they do not damage the bearing cag

安裝4個接頭墊塊，以免損壞軸承彈子盤蓋。

a alloy of tin with some copper and antimony; an anti-friction lining for bearings.

含錫和一些銅、銻的合金，用作軸承防摩擦襯墊。

Research Status and Prospect of Spherical Plain Bearings with Self-lubricating Fabric Liner

織物襯墊自潤滑關節軸承的研究現狀與展望

Provide non-standardized products：Cylindrical bushes, flanged bushes, thrust washers, flat strip material, half bearing, wear plate.

可供非標產品：直套、翻邊軸套，止推墊片、板材、軸瓦、滑板。

The Application of a Single Chip Processor 8098 to Detecting the Axial Clearance of a Bearing

8098單片機在軸承軸向間隙檢測中的應用

377 bolt (screw, nut, stud, spring washer, pin, ball bearing, roller bearing) is the most commonly used machine part.

螺栓（螺釘、螺帽、雙頭螺栓、彈簧墊圈、銷、滾珠軸承、滾柱軸承）是最常用的機械零件。

Research on Inner Rotor Type Disk Bearingless PM Motor;

內轉子式片狀無軸承永磁電機的研究

Finite Element Analysis of Bearing in Segment Erector System for TBM

TBM管片拼裝系統軸承有限元分析

Research Progress on Tribological Properties of Self-lubricating Materials Liner for Spherical Bearings

自潤滑關節軸承襯墊材料摩擦學性能的研究進展